DCS (WOTD-227) Double Oven Logo

Related Topics:

Posted on Nov 19, 2008
Answered

DCS wall oven very dim display for settings

Dim display

Answer This Question
  • Anonymous Nov 25, 2008

    Oven display very dim -- anyway it can be adjusted?

×

1 Answer

dcshelper

Level 1:

An expert who has achieved level 1.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.
Problem Solver:

An expert who has answered 5 questions.

  • Contributor 7 Answers
  • Posted on May 28, 2009
dcshelper
Contributor
Level 1:

An expert who has achieved level 1.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.
Problem Solver:

An expert who has answered 5 questions.

Joined: May 28, 2009
Answers
7
Questions
0
Helped
7573
Points
15

Typical for gas filled displays. check other postings for same problem for correction. part cost is $92.

1 Related Answer

Anonymous

  • 1 Answer
  • Posted on Oct 04, 2008

SOURCE: Dim LCD's on DCS Double Wall Oven

Had the same problem last week - called DCS (which automatically transferred me to Fischer-Paykel) and was able to order the part from them.  They knew exactly what it was, and shipped to me in CA from CA, it was less than $90.  Just installed it, and the new one works swell.  One suggestion - I drew with a Sharpie on one side of each of the three parts that plug into the board to help align the new one, and to install the wide ribbon cable (not really a cable, but you'll know what I mean), pull up on the two side pieces and the ribbon pulls right out.  Keep it up and slide the new one in and then push the black piece down.  That was the only part that took me a minute to figure out.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where can i buy a replacement control display
Hello Friends!
This dimming vacuum display is either caused by a power supply failure with the control board, or a the filaments of the display themselves have started to wear-- similar to that of a bad light bulb. Either way, FixYourBoard.com can solve this problem- This control board is no longer available to buy new. Contact FixYourBoard.com at 512-355-1108 for more information. The photo below is from a double oven, but they repair single oven displays too.
ch0509451-q0eqwqv0rnlb52n5vy4kutsd-1-0_1.jpg
Read full answer
Apr 13, 2017 • DCS Ovens
0helpful
1answer

I have DCS single wall oven model WO127 SS. Display is dim, again. Was repaired in '08 with part #211708. When I look for this part again, it says it fits WO130 with no mention of WO127. Genuine...
Good Morning Mr Villa!
FixYourBoard has repairs what youre experiencing in 2-3 business days. They'd remanufacture your part, and replace your dimming display, fully test the unit.. and back their work with a 2 year warranty. http://www.fixyourboard.com
Read full answer
Mar 30, 2017 • DCS Ovens
0helpful
2answers

Display is dim
Hello Friends! This dimming vacuum display is either caused by a power supply failure with the control board, or a the filaments of the display themselves have started to wear-- similar to that of a bad light bulb. Either way, FixYourBoard.com can solve this problem. Contact them 512-355-1108 for more information. The photo below is from a double oven, but we repair single oven displays too.
ch0509451-q0eqwqv0rnlb52n5vy4kutsd-1-0.jpg
Read full answer
Jan 16, 2013 • DCS WOS-227 Electric Double Oven
0helpful
1answer

The display - clock and the oven temp. readout on my DCS wall oven sometimes fades away to nothing and remains that way for days. Other times it may be dimly visible; usually after the oven has been...
the display or readout need to replace
Read full answer
Oct 03, 2010 • DCS WO-130 Stainless Steel Electric Single...
0helpful
1answer

Need a service manual for wo-127ss DCS single wall oven. need to replace the control board because my display light went out. How do I take it apart?
you can call dcs, they will be happy to send you a manual,
but mostly, this should be pretty simple, three small black phillips heads hold tthe console down, the are above the door when closed
from there the panel should tilt forward and off
becareful they dont leave much room. or very long wires
Read full answer
Oct 13, 2009 • DCS (WOTD-227) Double Oven
4helpful
2answers

Display on our dcs oven is beginning to fade. can i fix it?
Hello just repaired my DCS wall oven. LCD screen is no good. part # lcd only is 211708. cost is $85.00 dollars with shipping. Took me twenty minutes to install. just need one philips head screw driver.Just call DCS Fisher@Paykel 1-888-281-5698 new Zealand.
Read full answer
Oct 03, 2008 • DCS WO-130 Stainless Steel Electric Single...
4helpful
4answers

DCS elect wall oven LCD display
Had the same display issue with my DCS WOS-230. The display was fading and made it very hard to read clock and temp setting. Called DCS/Fisher Paykal and was told I need the Control system kit for $335.00 to fix the issue. After reading the input on this issue on this site I pushed them to sell me just the DCS EOC 211696 double display module 100-01095-00. Install took 10 minutes and everything works great. Thanks all for laying the groundwork as DCS will really push hard to sell you the more expensive kit that you do not need.
Read full answer
Jul 17, 2008 • DCS WO-130 Stainless Steel Electric Single...
2helpful
2answers

DCS Single Wall Oven Model WO-130-SS
Order part #211708 from 1-888-281-5698 DCS Fisher@Paykel new Zealand. Only need philips head screw driver and twenty minutes. This part is a upgrade for lcd only. old part was a three part system, but no need for three parts only lcd screen.
Read full answer
Jul 07, 2008 • DCS WO-130 Stainless Steel Electric Single...
9helpful
5answers

Dim LCD's on DCS Double Wall Oven
Had the same problem last week - called DCS (which automatically transferred me to Fischer-Paykel) and was able to order the part from them.  They knew exactly what it was, and shipped to me in CA from CA, it was less than $90.  Just installed it, and the new one works swell.  One suggestion - I drew with a Sharpie on one side of each of the three parts that plug into the board to help align the new one, and to install the wide ribbon cable (not really a cable, but you'll know what I mean), pull up on the two side pieces and the ribbon pulls right out.  Keep it up and slide the new one in and then push the black piece down.  That was the only part that took me a minute to figure out.
Read full answer
Jul 07, 2008 • DCS (WOTD-227) Double Oven
6helpful
2answers

DCS wall oven F7 ERROR
I TRIED SOLUTION FROM SYMAR DATED MAR 14, 08 IT WORKED FOR NOW. I HOPE IT WILL CONTINUE WORK UNTIL SERVICING...COME MORNING.
Read full answer
Feb 09, 2008 • DCS WO-130 Stainless Steel Electric Single...
Not finding what you are looking for?

View Most Popular

(WOTD-227) Double Oven

  • Ovens

Related Question

Where can i buy a replacement control display

  • DCS Ovens

Related Topics

939 views

Ask a Question

Usually answered in minutes!

Popular Questions

Dcs oven display dim - need part #

DCS (WOTD-227) Double Oven

Dim LCD's on DCS Double Wall Oven

DCS (WOTD-227) Double Oven

DCS elect wall oven LCD display

DCS WO-130 Stainless Steel Electric...

DCS Single Wall Oven Model WO-130-SS

DCS WO-130 Stainless Steel Electric...

Display on our dcs oven is beginning to fade. can i fix it?

DCS WO-130 Stainless Steel Electric...

Top DCS Ovens Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

NOEL
NOEL

Level 3 Expert

8606 Answers

Are you a DCS Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...